.

.

Search:

Type: Posts; User: Kyle H

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    59
    Views
    25,133

    Randy, Flat track racing is a way different...

    Randy, Flat track racing is a way different experience then on a king or hill climb. For this reason it can be very fun, and very challenging. Here are a few types of flat track classes that are most...
  2. Replies
    59
    Views
    25,133

    Glad you are getting good results EdC. We...

    Glad you are getting good results EdC. We typically use the R10 body. It seems to work well for us.
  3. Replies
    59
    Views
    25,133

    MentalKase, The steel used for the American PMP...

    MentalKase,
    The steel used for the American PMP chassis is a high cabon spring steel. In doing some research for the right type of steel to use for the PMP chassis I stumbled across some information...
  4. Replies
    59
    Views
    25,133

    Mic, were you running any weight in the front?...

    Mic, were you running any weight in the front? How many spacers did you have under the guide flag? Were you running skid pads on it? It sounds like you didn't have a lot of time to set up the car...
  5. Replies
    45
    Views
    23,286

    Wish I could make it there for this. To far for...

    Wish I could make it there for this. To far for me though... I hope some good video and/ or pictures and explanations are taken and posted though!
  6. Replies
    20
    Views
    6,060

    EdC, I have not tried the rear steer, but I know...

    EdC, I have not tried the rear steer, but I know others have. You would likely see an increase in sliding if you went to the .047 rails and see the chassis tightening up more as well.
  7. Replies
    20
    Views
    6,060

    EdC, the only noticeable difference between the...

    EdC, the only noticeable difference between the two set of instructions is that the instructions that I posted do not call for brass tubing in the rear of the rails to create rear steer.
  8. Replies
    59
    Views
    25,133

    Ok... How about this, it is almost gauranteed you...

    Ok... How about this, it is almost gauranteed you will see me at Nats... Almost.
  9. Replies
    59
    Views
    25,133

    No problem George. Glad this helps. Good luck and...

    No problem George. Glad this helps. Good luck and maybe I will see you at Nats.
  10. Replies
    20
    Views
    6,060

    Here is the approved chassis listing: ...

    Here is the approved chassis listing:

    http://www.slotcartalk.com/slotcartalk/showthread.php?32808-USRA-Div-2-2012-Aproved-Chassis-GT-12
  11. Replies
    59
    Views
    25,133

    Approved Gt-12 chassis listing: ...

    Approved Gt-12 chassis listing:

    http://www.slotcartalk.com/slotcartalk/showthread.php?32808-USRA-Div-2-2012-Aproved-Chassis-GT-12
  12. Replies
    59
    Views
    25,133

    George, thanks for your comments about the...

    George, thanks for your comments about the instructions. These chassis are difficult to put together so it is nice to have clear instructions. As far as being approved for the 2012 Nats, I have no...
  13. Replies
    20
    Views
    6,060

    Well that makes sense too. For the price of this...

    Well that makes sense too. For the price of this chassis its not too hard to have a backup that is setup differently.
  14. Replies
    20
    Views
    6,060

    Yes Gary... I am building a large section of most...

    Yes Gary... I am building a large section of most of the assembled chassis being sent out. That is how I know that the 0.047" rails are being used in assembly:D

    Maybe you could add some solder on...
  15. Replies
    20
    Views
    6,060

    Hahaha well that may be a good reason! You can...

    Hahaha well that may be a good reason!

    You can however replace your smaller daimeter wire with the larger wire to see how it works and change back if need be. Personally I like the 0.047" wire. I...
  16. Replies
    20
    Views
    6,060

    EdC, I have not experimented with the smaller...

    EdC, I have not experimented with the smaller rail sizes as I was instructed to use the 0.047" rails on my chassis when I built it and it has handled great so I haven't looked back.

    Perhaps Pedro...
  17. Replies
    20
    Views
    6,060

    No problem Mic. Customers ordering PMP kits...

    No problem Mic. Customers ordering PMP kits should be receiving instructions in their kits now that they are available. The instructions may or may not include pictures so this should be a helpful...
  18. Replies
    20
    Views
    6,060

    Good thread to get the most out of the PMP...

    Good thread to get the most out of the PMP Chassis:
    http://www.slotcartalk.com/slotcartalk/showthread.php?32004-My-first-GT12...-PMP-Chassis&highlight=my+first+chassis
  19. Replies
    20
    Views
    6,060

    2010 PMP GT-12 Chassis Instructions

    http://i249.photobucket.com/albums/gg202/kyle_a_hoff/Screenshot2011-10-25at43457PM.png
    http://i249.photobucket.com/albums/gg202/kyle_a_hoff/Screenshot2011-10-25at43516PM.png...
  20. Replies
    59
    Views
    25,133

    Thanks Pedro. I will give it a cleaning!

    Thanks Pedro. I will give it a cleaning!
  21. Replies
    59
    Views
    25,133

    It takes me about 2 hours to blueprint a PMP...

    It takes me about 2 hours to blueprint a PMP chassis. I have built more than a dozen now though... I'm going to be building at least another dozen starting some time next week too...

    Here are a...
  22. Replies
    83
    Views
    30,751

    I was wondering when we were going to see the...

    I was wondering when we were going to see the paint. They grey Blue color combo looks like it is going to be awesome! Can't wait to see it completed.
  23. Replies
    59
    Views
    25,133

    Myself and Jeremy were running .047" rails. I am...

    Myself and Jeremy were running .047" rails. I am not sure what Vance, "Odie" who won the GT-12 race or Dustyn "Dub" were running. The built chassis that are being sent out are assembled with the...
  24. Replies
    83
    Views
    30,751

    It looks like the G-16 is even hanging over the...

    It looks like the G-16 is even hanging over the taped off area :whistling: ooooppps haha. Its looking great.

    It is amazing to watch how the track starts to come alive as Gary puts the stripes...
  25. Replies
    83
    Views
    30,751

    Things are looking great Shontel! Can't wait to...

    Things are looking great Shontel! Can't wait to see it once the walls and stripes are painted!
Results 1 to 25 of 90
Page 1 of 4 1 2 3 4