.

.

Search:

Type: Posts; User: PitStopGuys

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. My condolences to "Bear's" friends and family. ...

    My condolences to "Bear's" friends and family. He was a good man.
  2. Replies
    31
    Views
    6,747

    I don't doubt that for a second and it doesn't...

    I don't doubt that for a second and it doesn't surprise me. The ease of use associated with a properly blueprinted T-Flex is (IMO) unsurpassed. It's ultimate performance, however, suffers in...
  3. Replies
    31
    Views
    6,747

    It is true that equalizing weight would reduce...

    It is true that equalizing weight would reduce chassis differences. I have yet to encounter a sanctioned scale racing program with minimum weights, so I consider this factor irrelevant.



    "Was"...
  4. Replies
    15
    Views
    4,580

    I also race at a track that requires 48-pitch...

    I also race at a track that requires 48-pitch gears. They do allow bevel pinions. Metal spurs are banned. Them's the rules.

    Anyway... angle/bevel pinions present their own problems. The...
  5. Replies
    15
    Views
    4,580

    That's helpful!

    That's helpful!
  6. Replies
    27
    Views
    5,908

    I hate to be a smart-***, but if they're wearing...

    I hate to be a smart-***, but if they're wearing too fast during water break-in maybe you should just cut the time you're running them in water. Rapid wear is a BIG problem circuit racing. That I...
  7. Replies
    23
    Views
    6,822

    Whoever your local raceway dude is, tell him the...

    Whoever your local raceway dude is, tell him the Kelly G2 can is available through Eagle or ERI.
  8. Replies
    27
    Views
    5,908

    Try a different set of brushes.

    Try a different set of brushes.
  9. Replies
    34
    Views
    11,868

    Poll: So have I but I don't let that stop me!

    So have I but I don't let that stop me!
  10. Replies
    41
    Views
    12,477

    Any distributors I have dealt with required...

    Any distributors I have dealt with required photographs of my raceway before shipping anything. This situation suggests that either a distributor hasn't noticed that the guy has no raceway anymore...
  11. Replies
    23
    Views
    5,647

    No, it won't.

    No, it won't.
  12. Replies
    23
    Views
    5,647

    On a given armature, inductance readings will...

    On a given armature, inductance readings will show a bad pole where the resistance readings will not.
  13. Replies
    1
    Views
    1,447

    I've seen the stuff...

    ...and it's pretty bad.

    What I want to know is who's supplying the parts to this guy? If he's buying a module and a turbo over the counter (at retail) and assembling them, what's the point of...
  14. Replies
    23
    Views
    6,822

    Good question. I suppose that depends on what...

    Good question. I suppose that depends on what you're looking for and how much the guy on ebay wants for the stuff. There are several suppliers of 16D magnets and more than one 'generation' of (for...
  15. Replies
    23
    Views
    6,822

    Those aren't USRA-legal. :eek: It was the...

    Those aren't USRA-legal. :eek: It was the magnets, last I knew. As it was told to me, the dimensions (thickness in particular) were not always above the legal minimum.

    Not to say that I haven't...
  16. Replies
    23
    Views
    6,822

    The "don't worry" advice is basically true, but...

    The "don't worry" advice is basically true, but not in the way I think you've taken it.

    1) Notching a magnet for axle clearance will mismatch the fields. That's just not an arguable point. The...
  17. Replies
    32
    Views
    9,261

    It's all about drift here at OWH. As they say......

    It's all about drift here at OWH. As they say... this must be the lowest spot on the internet 'cause everything loose rolls down here.:)
  18. Approximately 50 x 20.

    Approximately 50 x 20.
  19. Replies
    32
    Views
    9,261

    More correctly, it's a job opportunity for the...

    More correctly, it's a job opportunity for the lawyer... which is probably why the standard 3-wire is a bad idea.
  20. Hey, Ross... Nope. The shop had to close when...

    Hey, Ross...

    Nope. The shop had to close when they shut down the mall and tossed everyone out. If and when I reopen it will have to be in a much smaller space. Rents are kinda high these days...
  21. Thanks for the testimonial, John!

    Thanks for the testimonial, John!
  22. 180' Ogilvie Engelman for sale, Upstate, NY

    SOLD!

    Thanks.
  23. Replies
    10
    Views
    4,505

    The stock bar is .050" and not very stiff. I'm...

    The stock bar is .050" and not very stiff. I'm not surprised you bent it. The piano wire the guys have recommended will be a much better solution. And they're right... the only way to find out...
  24. Replies
    23
    Views
    6,822

    Monty,

    I'm aware of your opinions on probe type meters. I use my probe type in combination with my Trik Trax as I have come to the conclusion that some physical aspects of certain cans have negative...
  25. Replies
    23
    Views
    6,822

    Truer words, etc.

    Truer words, etc.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4