.

.

Search:

Type: Posts; User: Bill from NH

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Paul, i'm not racing much these days, but this...

    Paul, i'm not racing much these days, but this was good enough for me to save in WORD. Thanks for posting it.
  2. Replies
    2
    Views
    660

    Not me, but I believe Mike Swiss at Chicagoland...

    Not me, but I believe Mike Swiss at Chicagoland also sells these truers.
  3. At times, the local Walmart has has Mobil 1. I...

    At times, the local Walmart has has Mobil 1. I haven't checked recently.
  4. Edo is a colorful character who was heavily into...

    Edo is a colorful character who was heavily into slot cars back then, but about 8 yrs. ago or so, he suddenly stopped posting on the slot car bulletin boards. i don't know of anyone who knows what...
  5. Replies
    5
    Views
    2,024

    Dave, if you weren't around here for a year, then...

    Dave, if you weren't around here for a year, then we'd have problems & get concerned. <LOL>
  6. Thread: Raceway

    by Bill from NH
    Replies
    1
    Views
    314

    Paul, this video is of one of P.A.'s older...

    Paul, this video is of one of P.A.'s older locations with the Hasse Nielson king track. He's now in Houston with a Gary Gerding king track. The 2018 USRA
    Div.1 Nats were held there.
  7. I believe they're Maine's only surviving raceway.

    I believe they're Maine's only surviving raceway.
  8. Replies
    16
    Views
    1,864

    Sticky: Do you have to pass a breathalyzer before they...

    Do you have to pass a breathalyzer before they let you on the track? <LOL>
  9. I would bet not many, if any. When we had a local...

    I would bet not many, if any. When we had a local raceway in NH, they started using a set of Parma issued rules & revised them as time went on.
  10. Replies
    10
    Views
    1,287

    It should be a fun project. Post a photo here...

    It should be a fun project. Post a photo here when you get the car done.
  11. Replies
    10
    Views
    1,287

    Sam, one easy solution for fronts is to sleeve a...

    Sam, one easy solution for fronts is to sleeve a pair made for 1/8" axles with 1/8" brass or aluminum tubing. The big wings were run before 1973. Use wrap-arounds or whatever winging you're...
  12. Replies
    10
    Views
    1,287

    Sam, this chassis seems to be built for lots of...

    Sam, this chassis seems to be built for lots of flex. The front axle tube uprights both face forward, it appears the main rails are 1 of .063 & 1 of .055, with short half rails. It probably has other...
  13. i was surprised those weighted guides were even...

    i was surprised those weighted guides were even mentioned on "Between the Lanes." Those two parties aren't exactly bosum buddies.
  14. Replies
    6
    Views
    1,069

    Sam, i don't this individual, but those magnets...

    Sam, i don't this individual, but those magnets might not have been zapped when the photos were taken.
  15. Replies
    91
    Views
    8,529

    Sam, I haven't seen you post on the other board...

    Sam, I haven't seen you post on the other board for a few weeks. Are you still there?:whistling:
  16. Replies
    91
    Views
    8,529

    IMO, no, not for you & me, not unless it's in the...

    IMO, no, not for you & me, not unless it's in the hands of a driver who races in classes other than just lower/ beginner ones. These guys are usually more experienced anyway.
  17. Replies
    91
    Views
    8,529

    Chris, trolls are like this, ya know!

    Chris, trolls are like this, ya know! <LOL>
  18. Replies
    91
    Views
    8,529

    My first controller in 1967 was an MRC. I forget...

    My first controller in 1967 was an MRC. I forget it's color (maybe green?) & resistor ohmage. I ran a Russkit 23 powered car with it.
  19. Replies
    91
    Views
    8,529

    Sam, ignore works too.

    Sam, ignore works too. <LOL>
  20. Replies
    91
    Views
    8,529

    Or just state you want to use only MRC & Cox...

    Or just state you want to use only MRC & Cox controllers.
  21. Replies
    6
    Views
    2,673

    The same is true for soldered bushings &...

    The same is true for soldered bushings & bearings. I've done it afterwards too, but it's more work.
  22. Replies
    4
    Views
    2,580

    A wallpaper seam roller would be one tool that...

    A wallpaper seam roller would be one tool that could be used.
  23. Replies
    6
    Views
    2,673

    I put my painted motor cans in a warm oven (250...

    I put my painted motor cans in a warm oven (250 F) for 5-10 minutes. This would enhance the Cal Custom wrinkle paint I was using to wrinkle more.
  24. Replies
    6
    Views
    2,673

    When I used wrinkle paint years ago, I painted...

    When I used wrinkle paint years ago, I painted the cans before I glued in the magnets. I made a balsa plug to fit the cans that kept out paint & was something to hold on to. You could stuff yours...
  25. Replies
    3
    Views
    2,180

    if you do a Google search for Strombecker motors,...

    if you do a Google search for Strombecker motors, blue endbell ones show up too.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4