.

.

Search:

Type: Posts; User: salford13@sc.rr

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds; generated 25 minute(s) ago.

  1. Replies
    1
    Views
    1,576

    Building Own HO Scale Track

    Paul and All Fellow Racers,
    I Thank you ALL again for all your previous, answers, directions,
    instructions and support. They have been invaluable to me. But...
  2. Replies
    1
    Views
    998

    The different 15's?

    Hi guys,
    i have a question about group 15 motors. What is the difference between the b15, int. 15 and the spec 15? Thank you for your answers.
    ...
  3. Old Weird Harold, I...

    Old Weird Harold,
    I apologize to you also, I meant to say anglewinder.
    ...
  4. Rick B., Yes, I would appreciate a...

    Rick B.,
    Yes, I would appreciate a jig.
    Al. B.
  5. Bill From NH, I apologize, I...

    Bill From NH,
    I apologize, I did mean anglewinder motor box.
    AL. B
  6. Instructions and photos on 1/24 scale piano wire sidewinder rear axle and motor box support

    Guys,
    Does anyone have instructions and photos on how to construct a 1/24 scale piano wire sidewinder rear axle support and motor box? Thanks.
    ...
  7. 1/24 scale clear 4 and a 1/2 inch truck bodies

    Gentlemen,
    I'm having a little difficultly finding clear 1/24 scale 4 and a 1/2 truck bodies. Can anyone Please direct me? Thanks.
    ...
  8. I need to know again, Thank you...

    Gentlemen,
    What are the sources available to obtain blank stacks and comms? I'm just having a hard time believing that there is only one source of blank stacks and comms. Can...
  9. Paul, Thanks for that super fast...

    Paul,
    Thanks for that super fast response. Your reply was very complete. Thanks again.
    ...
  10. Is hot slots in gastonia, nc still open

    Gentlemen,
    i was wondering do you know if hot slots at 2825 west franklin blvd.in gastonia, nc. 28054 is still open? If it is do you know the phone number? If it is not do you...
  11. Thanks jdracer. Will try.

    Thanks jdracer. Will try.
  12. Matching endbell setup for viper adjustable timing c-can cans

    Hello again guys, i would like to know what endbell in particular, along with magnets, brushes and springs to use for a koford super wasp or s-16c arm in a viper (v-368) adjustable timing c-can to...
  13. Replies
    4
    Views
    2,473

    THANK YOU SLOTSRFUN APPRECIATE THE INFO AND...

    THANK YOU SLOTSRFUN APPRECIATE THE INFO AND DIRECTION.
    Al. B
  14. Replies
    4
    Views
    2,473

    Thanks monty will call wed. ...

    Thanks monty will call wed.
    Al.b.
  15. Replies
    4
    Views
    2,473

    Monty i need a bit of your wisdom

    Monty, as soon as mura responds i'll be ordering some (5) arms and comms to buid grp. 27 arms. As i researched grp. 27 arms are 27 guage wires of 38 turns. My questions to you are: 1) is mura the...
  16. Replies
    3
    Views
    2,001

    Carbon fiber hubs vs. Magnesium hubs

    Gentlemen, when is it better to use carbon hubs over magnesium hubs? And would drilling the hubs be to to any advantage? And of course who sells carbon hubs? Thanks.
    ...
  17. Replies
    13
    Views
    4,076

    fl_slotter I want to sincerely thank...

    fl_slotter
    I want to sincerely thank you for what I believe you told me is the fact of how rust results from using liquid flux but my problem is on the rear axles. I put cars together,...
  18. Replies
    13
    Views
    4,076

    Ok it's driving me crazy, rust!

    Gentlemen, i finally put my cars together and within a week the axles are rusted and this is before i race them. What can i do and buy to get rid of it and especially keep it away. Thank you.
  19. How far can I convert old controllers?

    Guys, I have two old Parma turbo controllers. I'd like to know is it possible and if it is, how do you convert these controllers into the ones like the pros use - Carsteen, Ruddock, DiFalco,
    3rd...
  20. Replies
    11
    Views
    3,179

    SteveDee, I did like you said except I used paint...

    SteveDee, I did like you said except I used paint thinner and it worked like a dream. I put the tires in a glass jar with a lid and let them soak for 24 hours occasionally shaking the jar. The only...
  21. Replies
    30
    Views
    6,107

    Just wanted to thank everyone for your answers...

    Just wanted to thank everyone for your answers and input. That question was very throughly answered.
  22. Replies
    11
    Views
    3,179

    Thanks stevedee for the recycle tip i have ten...

    Thanks stevedee for the recycle tip i have ten pairs to work with and i'll check out peiffer in a few days.
  23. Replies
    11
    Views
    3,179

    Wheel hubs and donuts

    Hello guys,
    can someone please tell me who sells 1/24 scale wheel hubs and donuts?
    Thank you.
    ...
  24. Ken Swanson, I just got a Mossetti Titan chassis...

    Ken Swanson, I just got a Mossetti Titan chassis and for some reason I got this feeling it may just be a good choice for GTP. Time and Testing will tell. Thanks.
    ...
  25. wjdougherty, What made it difficult to tune?

    wjdougherty, What made it difficult to tune?
Results 1 to 25 of 79
Page 1 of 4 1 2 3 4