​MSCS: Midwest Slot Car Series 2013/2014 Rules​
L.M.P
Chassis:
1. Any 4" chassis that is commercially available
2. Must be stamped and formed metal only
3. May brace chassis in any way
4. A steel guide tongue reinforcement may be used, but the original guide tongue may not be removed, modified, or moved
5. May use lightweight replacement pans, but must be from the same manufacture
6. Must use oilites; No ball bearings permitted

Gears/Axles/Wheels
1. 64 or 72 pitch gears
2. 11 tooth (64 pitch) or 12 tooth (72 pitch) pinion only
3. Solid Steel axles
4. Rear tires must be black foam; 0.750 minimum
5. Maximum width is 3 1/4"
6. 0.062 clearance at the back, up to the rear axle including the gear
7. No minimum at front, but front wheels must touch track if chassis is rocked side to side
8. Rear axle: 3/32"
9. Front axle 0.047 min or sticker fronts
10. No Speed Rubber

Lead Wires
1. Magnet wire or magnet type wire is not allowed
2. Guide clips are allowed
3. May add wire guide or retainer

Bodies
1. Bodies must be commercially available and on approved body list
2. Maximum rear spoiler height of 1 5/8". measured from the tech block to the top of the spoiler
3. Must have three scale appearing numbers
4. Bodies must be fully painted and cover the entire chassis
5. May reinforce body with tape or lexan
6. All windows must be clear and retain factory lexan
7. Front wheel wells may be cut out or left clear NO CUTTING INTO TOP OF THE FENDERS
8. Body must have fully painted 3D lexan interior; chassis or track must not be visible

Motor
1. JK Hawk 7
2. Fast Ones Demon
3. Trinity Evil 9


4" NASCAR
Chassis:
1. Any 4" chassis that is commercially available
2. Must be stamped and formed metal only
3. may brace chassis in any way
4. A steel guide tongue reinforcement may be used, but the original guide tongue may not be removed, modified, or moved
5. May use lightweight replacement pans, but must be from the same manufacture
6. Must use oilites; No ball bearings permitted

Gears/Axles/Wheels
1. 64 or 72 pitch gears
2. Solid Steel axles
3. Rear tires must be black foam; 0.750 minimum
4. Maximum width is 3 1/4"
5. 0.062 clearance at the back, up to the rear axle including the gear
6. No minimum at front, but front wheels must touch track if chassis is rocked side to side
7. Rear axle: 3/32"
8. Front axle 0.047 min; NO STUBBIES
9. No Speed Rubber
10. Front wheels 0.500 minimum; Can use O-ring front tire or Sticker Fronts

Lead Wires
1. Magnet wire or magnet type wire is not allowed
2. Guide clips are allowed
3. May add wire guide or retainer

Bodies
1. Bodies must be commercially available and on approved body list
2. Maximum rear spoiler height of 1 1/2" measured from tech block to the top of the spoiler
3. Must have three scale appearing numbers
4. Bodies must be fully painted and cover the entire chassis
5. May reinforce body with tape or lexan
6. All windows must be clear and retain factory lexan
7. Front wheel wells may be cut out or left clear NO CUTTING INTO TOP OF THE FENDERS
8. Body must have fully painted 3D lexan interior; chassis or track must not be visible
9. 1/8" minimum front and rear bumber
10. Interiors maybe mounted in stock-appearing location, but may not be floppy
11. NO C.O.T. BODIES




Motors
1. Parts must be commercially available
2. Any D-Can setup
3. Arms must be tagged American 16-D
4. Single ceramic magnets only
5. May epoxy or super glue magnets
6. No air gap honing is allowed
7. May use any 3 coil spring
8. May use any brushes; CUTTING OR DRILLING IS NOT PERMITTED
9. No aluminum end bells
10. Ball bearings in can only

Armature Specs
1. Minimum Diameter: 0.513"
2. Minimum Stack Length: 0.600"
3. Wire Size: AWG #30
4. Min Number turns per pole: 70
5. Tag: 16D


























GTP
Chassis:
1. Any 4" chassis that is commercially available
2. Must be stamped and formed metal only
3. may brace chassis in any way
4. A steel guide tongue reinforcement may be used, but the original guide tongue may not be removed, modified, or moved
5. May use lightweight replacement pans, but must be from the same manufacture
6. Must use oilites; No ball bearings permitted

Gears/Axles/Wheels
1. 64 or 72 pitch gears
2. Solid Steel axles
3. Rear tires must be black foam; 0.750 minimum
4. Maximum width is 3 1/4"
5. 0.062 clearance at the back, up to the rear axle including the gear
6. No minimum at front, but front wheels must touch track if chassis is rocked side to side
7. Rear axle: 3/32"
8. Front axle 0.047 min
9. No Speed Rubber
10. Front wheels 0.500 minimum; Can use O-ring front tire or Sticker Fronts

Lead Wires
1. Magnet wire or magnet type wire is not allowed
2. Guide clips are allowed
3. May add wire guide or retainer

Bodies
1. Bodies must be commercially available and on approved body list
2. Maximum rear spoiler height of 1 5/8" measured from tech block to the top of the spoiler
3. Must have three scale appearing numbers
4. Bodies must be fully painted and cover the entire chassis
5. May reinforce body with tape or lexan
6. All windows must be clear and retain factory lexan
7. Front wheel wells may be cut out or left clear NO CUTTING INTO TOP OF THE FENDERS
8. Body must have fully painted 3D lexan interior; chassis or track must not be visible
9. Floppy interiors not permitted





Motors
1. Parts must be commercially available
2. Any D-Can setup
3. Must be tagged "S16D" American Armature Only
4. Extreme S16D arms not permitted (No tie wrapping or com caps)
5. Single ceramic magnets only
6. May epoxy or super glue magnets
7. No air gap honing is allowed
8. May use any 3 coil spring ONLY
9. May use any brushes; CUTTING OR DRILLING IS NOT PERMITTED
10. No aluminum end bells
11. Ball bearings in can only

Armature Specs
1. Minimum Diameter: 0.513"
2. Minimum Stack Length: 0.490"
3. Wire Size: AWG #28
4. Min Number turns per pole: 60
5. Tag: S16D





















FCR
Beginner & Advanced

General Rules
1. FCR Beginner and Advanced will be ran together unless total entire is above 14 entires. In this case Beginner and Advanced will be ran seperate.

Chassis
1. Parma FCR 4.5'' Chassis #578
2. A steel guide tongue reinforcement may be used, but the original guide tongue may not be removed, modified, or moved

Gear/Axles/Wheels
1. 48 pitch gears ONLY
2. 9 tooth pinion ONLY
3. Oilies only; No ball bearing permitted
4. May use steel pinions
5. 1/8'' solid steel axles
6. Rear tires must me Parma FCR tires or Parma Tuna Tires
7. 0.062 clearance at the back, up to the rear axle including the gear
8. Must use stock axle spacers only
9. NO Offset permitted
10. May apply finger nail polish to front tires

Lead wire/Guide flag
1. Magnet wire or magnet type wire is not allowed
2. Guide clips are allowed
3. May add wire guide or retainer
4. May use any guide flag

Bodies

1. Bodies must be commercially available and on approved body list
2. Must have three scale appearing numbers
3. Bodies must be fully painted and cover the entire chassis
4. May reinforce body with tape or lexan
5. All windows must be clear and retain factory lexan
6. Body must have fully painted 3D lexan interior; chassis or track must not be visible
7. No Floppy interiors











Motors
1. Beginners
b. Sealed Parma 501 Death Star Only
c. May Solder can bushing in place
d. May use any brushes; CUTTING OR DRILLING IS NOT PERMITTED
e. Must use stock 5 coil springs
2. Advanced
a. Must use Parma 501 Death Star Armature ONLY
b. NO BALANCING of armature is allowed(drill or epoxy)
c. Must use Parma rotor can ONLY
d. Must use Parma 501 or 502 endbell and hardware ONLY
e. Must use Parma EPX Magnets ONLY
f. No air gap honing is allowed
g. No shimming of magnets is allowed
h. Must maintain .575"-.585" air gap
i. May use any brushes; CUTTING OR DRILLING IS NOT PERMITTED
j. May use any 3 coil springs
k. Ball Bearings are not permitted

Controller
1. Must use the Parma Turbo controller.














2013/2014 Approved Body List

4" NASCAR
Parma​​​​​1033 O6 Ford Fusion HD
​​​​​1046 Dodge Intrepid
​​​​​1014 Y2K4 MC HD
​​​​​1084 Ford Taurus

JK Products​​​​70527 Ford
​​​​​70524 Dodge
​​​​​70526 Chevy
​​​​​70525 Toyota

Outisight​​​​354 2K8 Stock Car
​​​​​238 Chevy Monte Carlo
​​​​​236 Dodge Charger
​​​​​234 Ford Fusion
​​​​​232 Toyota Camry

Kelly​​​​​1722 Taurus 01

Red Fox​​​​SC38C Camry

LMP
Parma​​​​​1048 Dome
​​​​​1083 MG EX257

JK Products​​​​7204 Lola B05
​​​​​7209 Lister

Outisight​​​​063 Ferrari 333
​​​​​290 Cadillac

Red Fox​​​​SC27C Lola C
​​​​​SC32C Caddy 05

GTP
ANY GTP STYLE BODY

FCR
Parma​​​​​1055CFC C.O.T
​​​​​

Page | 3